The 706 has the usual 1/8 th ″ CI-V remote control jack. To connect to a computer, you must purchase the Icon interface for $140, and a soundcard interface for $100 - OR NOT! This circuit will cost perhaps $25 (with case and cables and plugs) and does all these neat things. The Icom IC-7700 was designed from the start to be the ultimate contest transceiver. It employs the latest technology to give you the competitive edge. Two independent DSP units (of the same type used in the famous IC-7800) are built in: one for the transmitter & receiver and one for the spectrum display.
- Ci V Icom Software For Use With 7700 Wireless
- Ci V Icom Software For Use With 7700 Printer
- Ci V Icom Software For Use With 7700 Sewing Machine
- Ci V Icom Software For Use With 7700 Drivers
- Receivers
- Base Stations
- Base Stations
Download Type | USB Driver |
---|---|
Model name | IC-7100/IC-7200/IC-7300/IC-7410/IC-7600/IC-7610/IC-7850/IC-7851/IC-9100/IC-9700/IC-R8600 |
Version | Version 1.30 |
Update | 2018/06/07 |
Major changes | Changes in this version Windows 10 version 1803 (Jan 2019 update) is now supported. Notes
|
Note | |
File Size | 7.67MB |
File Type | ZIP |
Manual | manual download page |
Regarding this Download Service.
Ci V Icom Software For Use With 7700 Wireless
When using this download service, the implementation, use and/or results of use are the sole responsibility of you using this download service and the equipment. You shall comply with applicable laws and regulatory requirements in the use of this download service and in the operation of the equipment.
Firmware is important data for the basic system control of your equipment. An interruption during downloading or a malfunction may cause a failure in the data re-writing, and your equipment may stop functioning normally. If such a failure of the firmware re-writing results in your equipment not functioning normally, Icom Inc. and its affiliates expressly denies and is free from any and all responsibility arising from the result of damage from such an event.
You agree not to hold Icom Inc. and its affiliates responsible for any damage to your equipment operation or loss of data, or unauthorized use of the equipment, whether intentional or not, as a result of use this download service.
![With With](/uploads/1/1/8/9/118936207/958902657.jpg)
Add an external S-meter on any Icom amateur radio transceiver that has a CI-V control port.
![Ci v icom software for use with 7700 drivers Ci v icom software for use with 7700 drivers](/uploads/1/1/8/9/118936207/401410309.jpg)
- 5,479 views
- 2 comments
- 8 respects
Components and supplies
| × | 1 | |
| × | 1 | |
| × | 1 | |
| × | 1 | |
| × | 1 | |
| × | 1 | |
| × | 2 | |
| × | 1 | |
| × | 1 |
About this project
This circuit uses an Arduino Uno or Nano to send a CI-V command to an Icom radio to ask for signal information, read the answer, convert it and display it on an analog output, where you can connect an analog (Arsonval) S-meter.
It is powered by the Antenna Tuner port on the Icom radio. If your Icom does not have a tuner port, you can use any other port or connector that provides a +12V output (at least 200 mA). An external DC power source can also be used.
If you don't have an Antenna Tuner connector, you can use a PC computer power supply connector, and trim it with cutters to fit the Icom tuner connector.
This project is designed for an Icom IC-7000 transceiver, but it can be adapted to any Icom radio with a CI-V port.
You can use the CI-V '00' universal address on some Icom radios, making this converter compatible with any Icom radio, without changing the CI-V address in the code.
Ci V Icom Software For Use With 7700 Printer
Ferrites are installed on input & output cables to eliminate RF induction. The +12 V DC to the S-meter is not necessary; it could be used to power meter backlight or any other optional features.
The 10 k ohms potentiometer is used to attenuate the signal output (which is too high for most analog meters) and calibrate the analog meter to get a full scale reading with a powerful local signal (+60 dB).
Some other similar projects, using Arduino as a CI-V interface:
https://www.qsl.net/on7eq/en/ Click on 'projects' button
Code
Custom parts and enclosures
Schematics
Author
ddufault
- 2 projects
- 4 followers
Additional contributors
- The main idea, communication between arduino & ci-v port. by Luc ON7DQ
Ci V Icom Software For Use With 7700 Sewing Machine
Published on
July 19, 2019Write a comment
Members who respect this project
and 7 others
See similar projectsCi V Icom Software For Use With 7700 Drivers
you might likeTable of contents
Write a comment